点击图片查看大图|
主 要 技 术 指 标 |
|||
| 使用温度范围: | -30~70℃ | 插拔力: | / |
| 额定负荷: | DC 0.5A 30V | 湿度: | / |
| 接触电阻: | ≤0.03Ω | 线保持力: | / |
| 绝缘电阻: | ≥100MΩ | 适用线材: | / |
| 耐压: | AC 500V(50Hz)/min | 阻燃性: | / |
| 动作力: | 3~20N | 寿命: | 5000次 |
| 全回转角度: | / | 回转扭力: | / |
| 轴推拉强度: | / | 输出信号: | / |
| C.C数: | / | 分解度: | / |
| 定格电力: | / | 塑件: | / |
| 接触点: | / | 包装: | / |
| 间距: | / | 极数: | / |
| 适用基板厚度: | / | 其他: | |
|
产 品 图 纸 |
||||
|
|
|
KEWANG ELECRIC CO.,LTD |
文件編號 |
SF-SP-2005 |
|||||||
|
科 旺 電 子 有 限 公 司 |
發布日期 |
2005 年 12 月 9 日 |
|||||||
|
SPECIFICATION 規格書 |
第A 版 |
第 1 頁 共 3 頁 |
|||||||
|
MODEL NO. 產品名稱:耳机插座 |
|||||||||
|
DRAWN 制訂 |
周燕柳 |
APPD. 審 批 |
|
||||||
|
1. RATING (額 定 值) ：DC 30V 0.5A |
|||||||||
|
2. ELECTRICAL CHARACTERISTICS (電氣性能規格)： |
|||||||||
|
ITEM 項目 |
TEST CONDITIONS 測試條件 |
PERFORMANCE 規格 |
|||||||
|
2.1 |
CONTACT RESISTANCE 接觸電阻 |
MEASURED AT 1KHz SMALL CURRENT(100 mA OR LESS) 在1KHz微小電流(100mA 以下)測試. |
100mΩ MAX. 100毫歐以下。 |
||||||
|
2.2 |
INSULATION RESISTANCE 絕緣電阻 |
APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTAC (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED. 輸入500V DC電壓1分鐘,按以下接觸方法測試: (1) 插座體與排腳之間. (2) 不接觸的排腳之間. (3) 插頭插入時不接觸排腳之間. |
100MΩ MIN. 100兆歐以上。 |
||||||
|
2.3 |
DIELECTRIC STRENGTH 耐電壓 |
AC 500V rms(50-60Hz) FOR 1 MIN TRIP CURRENT:0.5 mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED. 輸入AC 500V(50-60Hz)電壓,1分鐘感度電流為0.5mA,按以下 接觸方法測試: (1) 插座體與排腳之間. (2) 不接觸的排腳之間. (3) 插頭插入時不接觸排腳之間. |
WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. 沒有絕緣破壞等異常. |
||||||
|
3 .MECHANICAL CHARACTERISTICS (機械性能規格) |
|||||||||
|
ITEM 項目 |
TEST CONDITIONS 測試條件 |
PERFORMANCE 規格 |
|||||||
|
3.1 |
CONNECTION FORCE 插 入 力 度 |
MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. 依據標準的PLUG GAUGE做3 次拔插后測定。 |
(0.3~2Kgf) |
||||||
|
|
DISCONNECTION FORCE 拔 出 力 度 |
MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. 依據標準的PLUG GAUGE做3 次拔插后測定。 |
(0.3~1.5Kgf) |
||||||
|
3.2 |
TERMINAL STRENGTH 端子強度 |
A STATIC LOAD OF 300gf SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC.IN ANY DIRECTION 在排腳前端任意一個方向加300gf力度測試,時間為15秒. |
THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY. ELECTRICAL AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED. 在排腳中沒有裂開.菘動等異常. 滿足于机械.電器性能。 |
||||||
